Load Balancing reference
Kong provides multiple ways of load balancing requests to multiple backend services: a straightforward DNS-based method, and a more dynamic ring-balancer that also allows for service registry without needing a DNS server.
Table of Contents
DNS based loadbalancing
When using DNS based load balancing the registration of the backend services is done outside of Kong, and Kong only receives updates from the DNS server.
Every API that has been defined with an
upstream_url containing a hostname
(instead of an IP address) will automatically use DNS based load balancing
if the name resolves to multiple IP addresses, provided the hostname does not
resolve to an
upstream name or a name in your
The DNS record
ttl setting (time to live) determines how often the information
is refreshed. When using a
ttl of 0, every request will be resolved using its
own dns query. Obviously this will have a performance penalty, but the latency of
updates/changes will be very low.
An A record contains one or more IP addresses. Hence, when a hostname resolves to an A record, each backend service must have its own IP address.
Because there is no
weight information, all entries will be treated as equally
weighted in the load balancer, and the balancer will do a straight forward
The initial pick of an IP address from a DNS record is not randomized. So when
using records with a
ttl of 0, the nameserver is expected to randomize the
An SRV record contains weight and port information for all of its IP addresses. A backend service can be identified by a unique combination of IP address and port number. Hence, a single IP address can host multiple instances of the same service on different ports.
weight information is available, each entry will get its own
weight in the load balancer and it will perform a weighted round-robin.
Similarly, any given port information will be overridden by the port information from
the DNS server. If an API has an
myhost.com resolves to a SRV record with
127.0.0.1:456 then the request
will be proxied to
http://127.0.0.1:456/somepath, as port
123 will be
The initial pick of an IP address + port combo is randomized, ensuring a proper
distribution, even with a
ttl setting of 0.
TIP: whenever the DNS record is refreshed a list is generated to handle the
weighting properly. Try to keep the weights as multiples of each other to keep
the algorithm performant, e.g., 2 weights of 17 and 31 would result in a structure
with 527 entries, whereas weights 16 and 32 (or their smallest relative
counterparts 1 and 2) would result in a structure with merely 3 entries,
especially with a very small (or even 0)
The DNS resolver will start resolving the following record types in order:
- The last successful type previously resolved
- SRV record
- A record
- CNAME record
So if the hostname you use has both SRV entries and A entries, it will start with SRV. If you want A records to be used, you must remove the SRV records from the DNS server. If you only have A records, then the SRV lookup will fail and it will fallback on an A query, etc.
When using the ring-balancer, the adding and removing of backend services will be handled by Kong, and no DNS updates will be necessary. Kong will act as the service registry. Nodes can be added/deleted with a single HTTP request and will instantly start/stop receiving traffic.
Configuring the ring-balancer is done through the
target: an IP address or hostname with a port number where a backend service resides, eg. "192.168.100.12:80". Each target gets an additional
weightto indicate the relative load it gets. IP addresses can be in both IPv4 and IPv6 format.
upstream: a 'virtual hostname' which can be used in an API
upstream_urlfield, e.g., an upstream named
weather.v2.servicewould get all requests from an api with
Each upstream gets its own ring-balancer. Each
upstream can have many
target entries attached to it, and requests proxied to the 'virtual hostname'
will be load balanced over the targets. A ring-balancer has a pre-defined
number of slots, and based on the target weights the slots get assigned to the
targets of the upstream. Incoming requests will be proxied in a weighted
Adding and removing targets can be done with a simple HTTP request on the management API. This operation is relatively cheap. Changing the upstream itself is more expensive as the balancer will need to be rebuilt when the number of slots change for example.
The only occurrence where the balancer will be rebuilt automatically is when the target history is cleaned; other than that, it will only rebuild upon changes.
Within the balancer there are the positions (from 1 to
slots) on the ring,
which each get a 'slot' assigned 1-on-1. Hence there are also
slots number of slots, but
they are randomly distributed over the ring positions. This randomness can be
set by using the
orderlist, but we strongly advice against doing that.
The randomness is required to make invoking the ring-balancer cheap at
runtime. A simple round-robin over the wheel (the positions) will do to
provide a well distributed weighted round-robin over the
also having cheap operations when inserting/deleting targets.
The number of slots to use per target should (at least) be around 100 to make
sure the slots are properly distributed. Eg. for an expected maximum of 8
upstream should be defined with at least
slots=800, even if
the initial setup only features 2 targets.
The tradeoff here is that the higher the number of slots, the better the random distribution, but the more expensive the changes are (add/removing targets)
upstream maintains a history of changes, targets can only be
added, not modified nor deleted. To change a target, just add a new entry for
the target, and change the
weight value. The last entry is the one that will
be used. As such setting
weight=0 will disable a target, effectively
deleting it from the balancer. Detailed information on adding and manipulating
targets is available in the
target section of the Admin API reference.
The targets will be automatically cleaned when there are 10x more inactive entries than active ones. Cleaning will involve rebuilding the balancer, and hence is more expensive than just adding a target entry.
target can also have a hostname instead of an IP address. In that case
the name will be resolved and all entries found will individually be added to
the ring balancer, e.g., adding
name 'api.host.com' resolves to an A record with 2 IP addresses. Then both
ip addresses will be added as target, each getting
weight=100 and port 123.
NOTE: the weight is used for the individual entries, not for the whole!
Would it resolve to an SRV record, then also the
from the DNS record would be picked up, and would overrule the given port
The balancer will honor the DNS record's
ttl setting and requery and update
the balancer when it expires.
Exception: When a DNS record has
ttl=0, the hostname will be added
as a single target, with the specified weight. Upon every proxied request
to this target it will query the nameserver again.